Tile isn’t waterproof. Grout isn’t either. Water gets through both, slowly, every time the shower runs, and what happens next depends entirely on what’s behind them. That layer, the waterproofing, is the one part of a bathroom remodel you’ll never see in a finished photo. It’s also the part that decides whether the bathroom is still dry in year ten.
Here’s what we build behind the tile on a bathroom remodel in San Diego, and why we fill the shower with water and walk away for a day before anyone sets tile.
What goes wrong when it’s skipped
A shower that was tiled over a bad pan doesn’t fail on day one. It fails quietly. Water wicks into the framing at the corners and the curb. Months later there’s a soft spot in the drywall outside the shower, a stain on the ceiling of the room below, grout that keeps cracking in the same spot, or a smell under the vanity that cleaning doesn’t fix.
By the time it’s visible, the fix is the shower. Tile out, pan out, framing checked for rot, sometimes subfloor. The homeowner pays for the bathroom twice. We’ve opened up showers like this in Poway and Rancho Bernardo where the tile looked fine and the studs behind it were black.
The assembly, layer by layer
Waterproofing is a system, not a product. Every piece has to connect to the next without a gap.
The pan. The shower floor under the tile is built to slope toward the drain, about a quarter inch per foot, so water that gets through the tile still finds its way out. The slope is set before the waterproofing goes on, because a flat pan holds water under the tile forever.
The drain connection. The drain is where most leaks start. The membrane has to bond to the drain flange with no gap, and the flange has to be the type that matches the membrane system. A clamping drain with a sheet liner and a bonded flange with a sheet membrane are two different assemblies. Mixing them is a leak.
The curb. The curb takes water from both sides and gets stepped on every day. It’s wrapped over the top and down both faces, with the corners sealed, and the top slopes slightly back into the shower so water runs the right way.
The walls. Membrane goes up the walls to at least the height of the shower head, and in our jobs usually to the ceiling. Every seam overlaps, every inside and outside corner gets a preformed piece or a reinforced patch, and every pipe penetration gets a seal. The shower valve and the shower head are the two spots where water is actively pushed against the wall, so they get the most attention.
The niche. The niche is a box cut into the wall and it’s the single most common leak point in a modern shower. It’s wrapped like a small shower of its own: every inside corner sealed, the shelf sloped toward the shower so water drains out rather than pooling.
The bench, if there is one. Same as the curb: wrapped over the top and down the face, top sloped, corners sealed.
We use bonded sheet membranes or liquid-applied membranes depending on the job, and we follow the manufacturer’s system from drain to wall. The manufacturer’s own instructions are the spec; a system installed by the book carries the manufacturer’s backing, and one that mixes parts doesn’t.
The flood test
Once the pan, curb and the lower walls are waterproofed and cured, we test it before covering anything.
- We plug the drain with a test plug below the membrane connection.
- We fill the pan with water, up to just below the top of the curb.
- We put a piece of tape at the water line and write the time on it.
- We leave. For 24 hours.
- We come back and look at the tape.
If the water is where we left it, the pan holds. We pull the plug, let it dry and tile can start. If the level dropped, there’s a leak, and we find it now, while fixing it means lifting a section of membrane, not demolishing a shower.
Membrane manufacturers describe the water test the same way: a quality-control check done before setting tile, with the assembly left for a set period, and 24 hours is typical (source: Schluter Systems, water test FAQ). Some inspectors want to see the pan under water themselves. Where the jurisdiction asks for a pan inspection, we schedule it around the test. Where it doesn’t, we run the test anyway.
Why 24 hours and not an afternoon
A bad drain connection shows up in an hour. The leaks that ruin bathrooms aren’t that kind. They’re a pinhole at a corner patch, a seam that’s bonded on 95% of its length, a flange that seeps a tablespoon an hour. In two hours the tape line hasn’t moved enough to see. In 24, it has.
The day costs us a day on the schedule. It’s the cheapest day in the whole job.
What this looks like from the homeowner’s side
For most of a day your new shower is a bathtub-shaped pool of water with a strip of blue tape on the wall. Nothing happens. No trades, no noise. It’s the only quiet day in a bathroom remodel and it’s the one we’d never give up.
If you’re comparing bids, this is a fair question to ask every bidder: “Do you flood test the pan, and for how long?” The answer should be a number of hours. “We’ve never had a problem” is not a number.
Common questions
Is a flood test required by code in San Diego?
Requirements vary by jurisdiction and by the type of pan. Some inspectors ask to see the pan under water before it’s covered; others sign off on the rough plumbing and leave the pan to the contractor. We treat the 24-hour test as our own standard on every tiled shower, whether or not the inspector asks for it.
Does a prefabricated shower base need a flood test?
A one-piece acrylic or composite base is its own waterproof layer, so the test shifts to the drain connection and the wall-to-base joint. We still check the drain for leaks before the walls close.
What about a curbless shower?
A curbless shower is waterproofed the same way, but the floor outside the shower is now part of the wet zone. The membrane extends across the whole bathroom floor and the slope has to be built into the subfloor, which usually means the floor is recessed. It’s more work, which is why it’s priced as its own scope.
How long after the membrane goes on can you test?
Sheet membranes need their thinset to cure, usually a day. Liquid membranes need to cure to the manufacturer’s spec between coats and before testing. So the waterproofing step is typically two to three days before the tile setter arrives, including the test.
Planning a bathroom?
Call (858) 392-6767. The first call is about 20 minutes: what’s wrong with the bathroom today, who uses it and what has to change. Then a site measure and a design conversation. The price comes after design, in a fixed-price contract, with the permit and the flood test written in. Our San Diego bathroom remodeling page walks through all six steps, and the order a bathroom remodel has to happen in explains why tile comes last.
IO Builders Group. Design-build, interior and outdoor. CSLB #1159596.